The Junk Man's Adventures
  • Home
  • How To Videos
  • Barn Fresh restoration
  • Toy Restorations
  • About the Junkman
  • The Junk Man's Blog
  • Service manuals
    • Impac Industries
  • JMG Behind the scenes
  • Media apperances
  • Current Sponsors

2/10/2023

Motorcycle Electro Testers

Comments

Read Now
 
motorcycle ignition tester unitThe mysterious "electro-tester"
Preservation of Knowledge:

​If you are new to working on vintage motorcycles, or even if you are not, chances are you have encountered suspect ignition components. Lets face it these early electronic components, ignition coil, magneto, CDI boxes, ect... are only getting older and older as time marches on.

Off to the internet you might say, right?  Well sure, that is probably what brought you here, however a lot of responses on the internet will say read your service manual and sure that IS the best starting point.  The service manual, especially the one published by the factory, is in fact the bible for your particular bike. 

​That is until you get to sections in that bible that reference certain factory tools for testing, tools that were not (then) and are not (now) readily available.  I am talking about certain specialty electronic component testers that were purpose built for factory dealership mechanics to use for servicing these old bikes when they were new.  I am talking specifically about a tool colloquially known as Electro-Testers.  Multi-function test equipment is nothing new.  In fact automotive OEM and aftermarket companies have been making all types of all-in-one type test equipment going all the way back to the early days of the automobile.  The problem with these specialty purpose tools is they can fall out-of-date as the years roll on and engine management technology changes and evolves.

Sun Engine Performance TesterAutomotive Engine performance tester
And here lies the problem with a hobbyist that is trying to keep a motorcycle on the road some 50+ years later.  These tools become as hard to find as the knowledge that goes with them. I thought it would be fun to take a look at a few of these specialty tools from a by-gone era and demystify what some of them do.

What is an Electro-Tester?

CDI unit test processKawasaki CDI unit test outlined in the service manual
In the context of vintage motorcycles, an electro tester is a device that combines many diagnostic testers into one conveniently packaged unit.  Most of these units encompass all the necessary tester functions related to ignition & sometimes lighting/charging into a box with specific test leads or connectors for each specific component that may need testing.  This was done to make quick work of determining if a motorcycle electrical component, for example an ignition coil, was "good" or not.

Why not just use a multi-meter?  True, this is a viable option and most service manuals will reference procedures and values for using an off the shelf multi-meter, which is how most at home DIY'ers will have to diagnose specific electrical components.  The benefit of these (previously) dealer only tools is that they were compact, contained all the tests in one box and were a, quick plug it in and read the dial, to determine a GO or NO-GO component.  The goal was speed, repeatability and reliability. 

What was really appealing about these devices is some of them could test CDI boxes for certain models. In some Kawasaki manuals it even stated if an Electro-Tester was available (see inset) use the instructions that came with the tester to determine if the CDI unit was good.  Sometimes an alternative method with a multi-meter was either not presented or very complex and subjective.  Using one of these test boxes would have been a quick task for a mechanic that is on the clock.

SO what can some of these all-in-one electro testers do?

Below are some common functions and tests these testers in a box can do, regardless of the manufacturer.
closeup ignition coil testSpark test (Ignition coil test)
Spark Test Gap/Ignition Coil Test

One of the most useful tests is the ignition coil test.  Test leads are attached to the high tension (spark plug) coil. A voltage generated from the tester is used to jump the gap between the two pointed electrodes.  A dial is used to vary the gap as the coil is tested as viewed through an observation window.  Quality of the spark can be viewed and depending on the maximum gap the spark can jump will determine the quality of the coil.

Note: The 3rd electrode is not connected to anything. Its function is to help propagate the initial spark to the opposing electrode when starting the test.

PictureTachometer & Dwell angle combination gauge
Tachometer/RPM

A tachometer to read engine RPM's was sometimes included on these testers.  While not really a test in of itself, the tachometer hooked leads to the spark plug wire and used the ignition firing pulses to then calculate the engines RPM via a sweeping needle indicator.  A selector dial to selector between 2 and 4 stroke.
The tachometer would have been a useful tool for mechanics working on motocross bikes that didn't have a cable operated tachometer to set things like the idle speed, carburetor tuning at specific RPM's, and testing charging voltage/amps during night time operation.  Also this would have been a bit more accurate than a cable operated gauge as those get progressively inaccurate the faster they spin due to frictional losses in the gear train that make them work.

PictureIgnition timing light function
Timing Light

Again, not a specific test but a tool to be used in conjunction with other features of the tester.  A timing light can help on bikes that have adjustable timing by flashing a light  when the spark plug fires.  Using the service manual a mechanic can quickly set timing advance on bikes that require it.

PictureDwell angle adjustment procedure for up to a 4 cylinder engine
Dwell angle test (see previous tachometer picture)

A test that is specifically for setting accurate timing for contact breaker point type ignitions.  The tester can give a readout of the rotational angle (or percentage) of the time the contact breaker points are closing.  The service manual will give a value for this and the mechanic can use this mode to slowly open or close the point gap to achieve the correct ignition timing.

PictureCondenser test
Condenser capacity test

Related to contact breaker point type ignitions are the capacitors that store up energy that is released through the points and then is stepped up by the high tension (spark plug) coil.  Some testers have a mode to test the capacity, displayed as MF (microfarad).  When in this mode the capacitor will be charged and its capacity can be measured.  The service manual will give a specific value that the capacitor should read.  This can make quick work of ruling out a faulty condenser when diagnosing ignition problems.

Picture"CDI Check" consolidates these multi-meter tests into a single opperation
CDI, PEI, Ignition box test

A simple GO/NO GO test using some internal circuitry to determine a functioning or non functioning ignition box.  The actual way the tester determines this is a bit of a mystery at this time. However anecdotal experience is that this test could result in false positives/negatives.  More research would need to be done, however back in the day when the electronics were not degraded it was probably fairly accurate at determining faulty CDI boxes on used bikes.

Examples of electro-testers from various motorcycle brands

Kawasaki Electro Tester srk-5010
Kawasaki Electro Tester
Suzuki Electro Tester
Suzuki Electro Tester
Suzuki tester
Suzuki Electro Tester quick guide
Suzuki SS-II tester
Suzuki Electro Tester close up
Yamaha motorcycle electro tester
Yamaha Electro Tester
yamaha tester instructions
Yamaha tester instructions
Honda had something similar, but simply called it a SERVICE TESTER, however the functions were pretty much the same as Suzuki and Kawasaki's version in function.
Honda electro tester service
Honda Service Tester
Honda electro tester
Honda Service Tester accessories
Honda Service Tester instructions
Honda Service Tester instructions
And just in case you thought these tools were just for motorcycles they were pretty common for gasoline automotive applications as well.  Here is an example that has bundled connectors for various applications of CDI units that would have come on early cars that had electronic ignition.
Automotive spark tester
A typical ignition tester designed for automotive use

Share

Comments
Details
    Subscribe to me on YouTube

    Author

    Jon "the junk man" helping to promote responsible riding and recreation whether it be at the track or at the trail. Your source for motorcycle how to videos and much more!

    Picture
    How To Videos
    How To Articles
    In The Media

    Archives

    February 2023
    January 2023
    May 2022
    December 2020
    August 2020
    July 2020
    February 2020
    January 2020
    October 2019
    September 2019
    August 2019
    July 2019
    April 2019
    March 2019
    January 2019
    November 2018
    July 2018
    June 2018
    May 2018
    March 2018
    February 2018
    January 2018
    December 2017
    October 2017
    September 2017
    August 2017
    July 2017
    March 2017
    February 2017
    December 2016
    November 2016
    October 2016
    August 2016
    July 2016
    June 2016
    May 2016
    April 2016
    March 2016
    February 2016
    January 2016
    December 2015
    October 2015
    August 2015
    July 2015
    June 2015
    May 2015
    April 2015
    March 2015
    February 2015
    January 2015
    December 2014
    November 2014
    October 2014
    September 2014
    August 2014
    July 2014
    June 2014
    May 2014
    April 2014
    March 2014
    February 2014
    January 2014
    March 2013
    February 2013
    January 2013
    December 2012
    November 2012
    October 2012
    August 2012
    July 2012
    June 2012
    May 2012
    April 2012
    March 2012
    January 2012
    November 2011
    October 2011
    September 2011
    August 2011

    RSS Feed

    Blog Directory & Business Pages - OnToplist.com
Proudly powered by Weebly
  • Home
  • How To Videos
  • Barn Fresh restoration
  • Toy Restorations
  • About the Junkman
  • The Junk Man's Blog
  • Service manuals
    • Impac Industries
  • JMG Behind the scenes
  • Media apperances
  • Current Sponsors